急～～英文翻译

发布网友发布时间：2022-04-22 08:53

共4个回答

热心网友时间：2023-08-29 20:37

1, from proct materials, the first materials we examine relevant data about the results, this material is suitable for sand casting. But from the proct structure and tolerance, proct design intent is supposed to die. We checked the chemical composition of materials, the material should be die-casting, therefore we plan to quote by casting. Considering the following requirements for proct, we plan to make this by vacuum die-casting procts.
2, e to the requirement of die-casting procts are stripping, proct must be pulling mould processing, and customers can rake without specified in the drawing, so we do look for customers, stereo stereo taper Angle of our design is unilateral 1 degrees, considering the procts material shrinkage is larger, we think taper Angle is less than 1 degree will be difficult to die. Because we don't know the specific purposes, so all we do is pulled, mold design if you have special request, please consider our change mould structure or use for subsequent processing to ensure drawing.
3, considering the mechanical properties of the procts, we suggest that the cutting edge procts (i.e., pointed) can instead that can rece proct may proce the stress, the mechanical properties of the procts after heat treatment will be better. We are doing when stereo change to R0.3 cutting edge. This change does not know whether to proct assembly or structure. If yes, please particularly pointed to, we will consider using subsequent processing moulds or change to ensure proct performance requirements.
4 and possible for us, please indicate the key control size, in order to we open mode and proction in time pay special attention.
5. These Suggestions are in order to save cost, to quote the best price for your company.

热心网友时间：2023-08-29 20:38

1 first about the material from the proct, the proct material information about us check the result, this material is suitable for sand casting. However, the proct structure and tolerance considerations, proct design intent should be required casting. We investigate the chemical composition of this material, this material should be able to die, we plan to report using die-casting. Proct requirements taking into account the follow-up treatment, for which we plan to use the vacuum casting to proce this proct.

2 e to the requirements of die casting mold release procts, this proct must have a taper angle to processing, and customer drawings are not specified, for which we do look three-dimensional map to the customer, three-dimensional graph drawing mode We designed the unilateral slope 1 degree, consider this proct the material shrinkage rate is relatively large, we believe that less than 1 degree taper angle would be more difficult to die. Because we do not know the specific use of the proct, for all we have done face pull-mode design, if there are special requirements please ask, we then consider changing the structure or mold used to ensure the drawing up processing requirements.

3, taking into account the mechanical properties of the proct, we recommend procts, sharp edges (ie sharp corners) can be replaced by rounded corners, thus recing the proct may have internal stress, mechanical properties after heat treatment procts will be better. We do three-dimensional diagram, have sharp edges to the R0.3. This change does not know whether the impact of proct assembly or structure. If so, please highlight, we will consider changing the mold, or by subsequent processing to ensure proct performance requirements.

4, if possible, please indicate the key control for our size, so that we can mold and proction at a time when special attention.

5. All these proposals are aimed at better save processing costs, in order to report the best price for your company.

热心网友时间：2023-08-29 20:38

1、From proct information about procts, we find this material information about the result is that the material for the cast. but the proct and tolerance, proct design should be required over cast. we have been the material of chemical components. this material will be cast down, we plan to adopt the attached to paper. consider the request in subsequent treatment for this proct, we plan to use the vacuum pressing have to make this proct
2、The press release of the proct is attached to the proct must have pulled the slopes to processing mole and blueprint have no specific mention in the client, so we made a block diagram to your customers see, the solid figure out of the slopes of course we are unilaterally 1, considering the proct of the material larger shrinkage, we think the slopes up to be less than 1 degrees would be difficult to cast down. because we don't know the specific purpose for which all sides we all had drawn by design, if there are special toensure the drawing up processing requirements
3、Considering the mechanical properties, we recommend that the sharp edge of the red caltrop ）（ able to use so may rece the procts that may arise in the treatment of the mechanical procts can be better. we are making a solid figure, the sharp edge to r0. 3. such changes did not know whether the proct assembly or structure is affected. if there is particularly pointed out, please, we will consider changing the mould or follow-up process to ensure that the proct requirements
4、Possible for us to indicate the key to control the size, so we are open and proction of special attention.
5、These proposals are to be more economical processing costs so as to offer you most favorable prices for your company

热心网友时间：2023-08-29 20:39

1, first about the material from the proct, the proct material information about us check the result, this material is suitable for sand casting. However, the proct structure and tolerance considerations, proct design intent should be required casting. We investigate the chemical composition of this material, this material should be able to die, we plan to report using die-casting. Proct requirements taking into account the follow-up treatment, for which we plan to use the vacuum casting to proce this proct.
2, e to the requirements of die casting mold release procts, this proct must have a taper angle to processing, and customer drawings are not specified, for which we do look three-dimensional map to the customer, three-dimensional graph drawing mode We designed the unilateral slope 1 degree, consider this proct the material shrinkage rate is relatively large, we believe that less than 1 degree taper angle would be more difficult to die. Because we do not know the proct's specific use, Weici all of Mian we have done everything pull mold design, if The special demand Tichu come we have to reconsider Genggai mold structure or Caiyonghouxu processing requirements to ensure the drawing of.
3, taking into account the mechanical properties of the proct, we recommend procts, sharp edges (ie sharp corners) can be replaced by rounded corners, thus recing the proct may have internal stress, mechanical properties after heat treatment procts will be better. We do three-dimensional diagram, have sharp edges to the R0.3. This change does not know whether the impact of proct assembly or structure. If so, please highlight, we will consider changing the mold, or by subsequent processing to ensure proct performance requirements.
4, if possible, please indicate the key control for our size, so that we can mold and proction at a time when special attention.
5. These proposals are aimed at better save processing costs, in order to report the best price for your company.